New Owner Here
New Owner Here
Just picked up a 1950 4A. Runs, drives and stops. Has some minor niggles, but nothing out of the ordinary for British cars. While I am looking forward to the challenge of finding parts, thought I would start by seeing if anyone can direct me towards options for oil filters, adaptors, or spacers. Rubber seal at bottom of windshield above scuttle, and although I think I asked this earlier, exhaust system suggestions. Mine is toast. I can have one fabricated by a local exhaust shop or if you all recommend something I will take a look. Thank you for your consideration.
Scott
Scott
Re: New Owner Here
Scott: Did you have any luck finding parts? I have a 1951 4A very much apart and in need of an engine. If you know of an engine, I'd appreciate the lead. Matt
Re: New Owner Here
Hey Scott
I owned and restored Singer Roadsters for many years before going totally pre-war. My only post-war Singer now is 1928, which means post great war!
Paul Beck in the UK carries a great conversion for the oil filter:
https://www.vintagecarparts.co.uk/produ ... tridge-zr1
Details:
This filter has the following original references - AC ZR1, Crossland 473, Crossland A40U, Fram PS5PL, Fram PS5A, Wipac CA453, Wix 5T, Wix WF5.
ASCO in the UK should be able to supply the rubber windshield sealing strip. The late Bill Haverly, the famous ASCO Roadster Registrar, used to have batches made. It has a particular profile. Dave Green, our NASOC parts man may also have a couple in stock. Paul Beck can probably supply a more generic version that will work as well. He has a good line of rubber items.
Woolies in the UK carries this item that will work also. I use it on my pre-war cars:
http://www.woolies-trim.co.uk/p-1798-ru ... usion.aspx
The most popular muffler for the Roadster seems to be one adapted from a Ferguson tractor. The original was actually quite long and hangs on a rubber mounting ( the same as used on the leaf springs ) outside the chassis rail. I used to use a round Thrush performance muffler as it had an original look and was cheap and easy to replace. Not sure that these are sold any more. My last Roadster had a stainless steel system by Bill Haverly.
Hope that helps!
Cheers,
Phillip
I owned and restored Singer Roadsters for many years before going totally pre-war. My only post-war Singer now is 1928, which means post great war!
Paul Beck in the UK carries a great conversion for the oil filter:
https://www.vintagecarparts.co.uk/produ ... tridge-zr1
Details:
This filter has the following original references - AC ZR1, Crossland 473, Crossland A40U, Fram PS5PL, Fram PS5A, Wipac CA453, Wix 5T, Wix WF5.
ASCO in the UK should be able to supply the rubber windshield sealing strip. The late Bill Haverly, the famous ASCO Roadster Registrar, used to have batches made. It has a particular profile. Dave Green, our NASOC parts man may also have a couple in stock. Paul Beck can probably supply a more generic version that will work as well. He has a good line of rubber items.
Woolies in the UK carries this item that will work also. I use it on my pre-war cars:
http://www.woolies-trim.co.uk/p-1798-ru ... usion.aspx
The most popular muffler for the Roadster seems to be one adapted from a Ferguson tractor. The original was actually quite long and hangs on a rubber mounting ( the same as used on the leaf springs ) outside the chassis rail. I used to use a round Thrush performance muffler as it had an original look and was cheap and easy to replace. Not sure that these are sold any more. My last Roadster had a stainless steel system by Bill Haverly.
Hope that helps!
Cheers,
Phillip
Your Friendly Canadian Pre-War Singer Specialist, Collector & Historian,
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Re: New Owner Here
Philip, thanks so much for the insight. I am now to the point where I am piecig the car back together. It is complete for the most part, but as you well know a slow labor of love with prepping all parts for reassembly.
I ended up buying 2 stock oil filters from the UK Singer Club Stash, and I ended up with a "patch" exhaust from a tractor. A little loud, but I daylighted the exhaust tip right at the back of the drivers door. I will have it reworked for exit out of the back of the car. Hopefully making it slightly "quieter" in the cockpit.
I appreciate you taking the time to respond. I may trouble you with more questions, if you don't mind as the reassembly moves forward.
Scott
I ended up buying 2 stock oil filters from the UK Singer Club Stash, and I ended up with a "patch" exhaust from a tractor. A little loud, but I daylighted the exhaust tip right at the back of the drivers door. I will have it reworked for exit out of the back of the car. Hopefully making it slightly "quieter" in the cockpit.
I appreciate you taking the time to respond. I may trouble you with more questions, if you don't mind as the reassembly moves forward.
Scott
Re: New Owner Here
Hey Scott,
My pleasure to assist and please feel free to ask questions. I have some Roadster spares left over so if you are looking for anything, please ask. I might post a lot of the stuff in the parts for sale once I get a chance.
The following info may help in regards to mufflers: It's been a few years since my last Roadster, but I think the exhaust tube diameter was @ 1 1/2".
These were two options in the tractor range:
1: Massey- Ferguson Muffler, horizontal, round. 1-1/2" inlet ID, 1-1/2" outlet OD, 34" OA length, 3-1/4" diameter. Tractors: TO20, TO30, TO35 Continental gas; MF35 Perkins diesel, MF135.Product No. -- 505545M92 | UPC -- 758351771017
2: Horizontal MUFFLER Ford 2N 2-N 8N 8-N 9N 9-N Tractor
Heavy-duty horizontal muffler. Inlet 1-1/2" I.D., outlet 1-1/2" O.D., body length 23". Tractors: 9N, 2N, 8N (1939-1952). -- M1002
Photo as follows:
It would be easy to cut down the outlet tube length and add the standard design Roadster tailpipe. The body length of 23" needs to be checked to ensure that it fits in the space along the frame rail under the running board. These certainly have a period look!
Cheers,
Phillip
My pleasure to assist and please feel free to ask questions. I have some Roadster spares left over so if you are looking for anything, please ask. I might post a lot of the stuff in the parts for sale once I get a chance.
The following info may help in regards to mufflers: It's been a few years since my last Roadster, but I think the exhaust tube diameter was @ 1 1/2".
These were two options in the tractor range:
1: Massey- Ferguson Muffler, horizontal, round. 1-1/2" inlet ID, 1-1/2" outlet OD, 34" OA length, 3-1/4" diameter. Tractors: TO20, TO30, TO35 Continental gas; MF35 Perkins diesel, MF135.Product No. -- 505545M92 | UPC -- 758351771017
2: Horizontal MUFFLER Ford 2N 2-N 8N 8-N 9N 9-N Tractor
Heavy-duty horizontal muffler. Inlet 1-1/2" I.D., outlet 1-1/2" O.D., body length 23". Tractors: 9N, 2N, 8N (1939-1952). -- M1002
Photo as follows:
It would be easy to cut down the outlet tube length and add the standard design Roadster tailpipe. The body length of 23" needs to be checked to ensure that it fits in the space along the frame rail under the running board. These certainly have a period look!
Cheers,
Phillip
Your Friendly Canadian Pre-War Singer Specialist, Collector & Historian,
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Re: New Owner Here
H Phillip,
I ended up with a different shorter and I assume noisier trctor muffler. So I will take a look at the one you recommend, I am also interested in parts, so if you are open to send me the details, my e-mail address is: a56healey@gmail.com.
Thank you again
Scott
I ended up with a different shorter and I assume noisier trctor muffler. So I will take a look at the one you recommend, I am also interested in parts, so if you are open to send me the details, my e-mail address is: a56healey@gmail.com.
Thank you again
Scott
Re: New Owner Here
Hey Scott,
Here's a great photo from Fred Tag's 4AD restoration album. Looks like he may have used the muffler I mentioned...or something very similar:
This is a great view to show the location and set-up of the muffler assembly. Fred mounted the system differently to the original, but the installation is sweet!
I'll be in touch with a list of spares...
Cheers,
Phillip
Here's a great photo from Fred Tag's 4AD restoration album. Looks like he may have used the muffler I mentioned...or something very similar:
This is a great view to show the location and set-up of the muffler assembly. Fred mounted the system differently to the original, but the installation is sweet!
I'll be in touch with a list of spares...
Cheers,
Phillip
Your Friendly Canadian Pre-War Singer Specialist, Collector & Historian,
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Re: New Owner Here
Thanks Phillip, I was in the process of posting this picture but you beat me to it. Yes it is the same muffler as shown above, I acquired mine from Summit Racing. The OEM mounting calls for one single large support clamp in the center of the muffler which attaches to the frame rail. As I can tell, that is the only support between the back of the car and the exhaust manifold. I was a bit uncomfortable with that so I decided to take advantage of the body mount lugs and positioned the exhaust pipe/muffler joints directly under them. The flexible hangers are bolted to the frame and attach to the clamps that secure the muffler to the pipes. This setup seems flexible enough but with a little extra security. I used cheap PVC pipe to make a pattern for the exhaust pipes, using heat to form it where the bends would go. I then took the patterns to a local muffler shop who custom made the front and rear pipes. After checking the fit, cutting them to proper length, and carefully positioning the exhaust manifold flange to the front pipe, I returned to the muffler shop for welding.
Hope this helps, have a great day!
Fred
Hope this helps, have a great day!
Fred
Re: New Owner Here
Thanks Fred and Phillip. Absolutely helpful. I will check out Summit Racing for the muffler.
Scott
Scott
Re: New Owner Here
Hey Fred,
Something slightly hilarious about the fact that Summit Racing sells tractor mufflers!
It is indeed the same beast!
Something slightly hilarious about the fact that Summit Racing sells tractor mufflers!
It is indeed the same beast!
Your Friendly Canadian Pre-War Singer Specialist, Collector & Historian,
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Editor & Pre-War Registrar & Canadian Contact -NASOC
Singer Enthusiast for over 40 Years.
'28 Senior, '33 & '34 Sports, '36 Le Mans SS & Bantam
Re: New Owner Here
hi,
i take the liberty to hi-jack this thread.
i own a 4AD from 1952.
it came with only part of the exhaust pipe sytem intact.
the muffler itself is no problem, but where does the pipe run to the back,
between the wheel and the body,
under the rear axsel or
above the rear axel
hope you can assist me
klaus lundsgaard
denmark
i take the liberty to hi-jack this thread.
i own a 4AD from 1952.
it came with only part of the exhaust pipe sytem intact.
the muffler itself is no problem, but where does the pipe run to the back,
between the wheel and the body,
under the rear axsel or
above the rear axel
hope you can assist me
klaus lundsgaard
denmark
- mikeyr
- Site Admin
- Posts: 1347
- Joined: Thu Nov 17, 2005 10:20 am
- First Name: Mike
- Location: S. Calif.
- Contact:
Re: New Owner Here
On the main website, under "everything 4AD" are the following drawings that should help figure out the exhaust.
http://www.singercars.com/4ax/4AD_mtc.html
http://www.singercars.com/4ax/ptwelve.html
http://www.singercars.com/4ax/4AD_mtc.html
http://www.singercars.com/4ax/ptwelve.html
Mike Rambour. Site Administrator
1953 Singer 4ADT (sold), 1934 Singer 9 Le Mans, 1934 Singer 1 1/2 4-Seater Sports (sold), 2009 BMW K1300GT
1953 Singer 4ADT (sold), 1934 Singer 9 Le Mans, 1934 Singer 1 1/2 4-Seater Sports (sold), 2009 BMW K1300GT
Re: New Owner Here
thank you very much.
very clearly now.
klaus
very clearly now.
klaus