Search found 82 matches

by indian301
Fri Aug 18, 2017 3:51 pm
Forum: 4's and up
Topic: Ring Gear for 4A
Replies: 7
Views: 193

Re: Ring Gear for 4A

The ring gear should tap off the flywheel, but You will need to heat it up to install it again.
by indian301
Sat Jun 17, 2017 12:25 pm
Forum: 4's and up
Topic: Looking for parts '54 4AD
Replies: 5
Views: 184

Re: Looking for parts '54 4AD

Any competent driveline shop can retube your driveshaft if you can't find a good used one.


Dave
by indian301
Mon Apr 10, 2017 6:18 pm
Forum: 4's and up
Topic: Complete frame
Replies: 6
Views: 283

Re: Complete frame

Where are you located?

Dave
by indian301
Tue Aug 30, 2016 4:20 am
Forum: 4's and up
Topic: 4 AD for sale on ebay
Replies: 0
Views: 262

4 AD for sale on ebay

Nothing to do with me. 1953 4ad for sale on ebay
by indian301
Thu Jun 30, 2016 12:40 am
Forum: 4's and up
Topic: Valve Job - Cam, Lifters, Etc - Where to buy
Replies: 3
Views: 288

Re: Valve Job - Cam, Lifters, Etc - Where to buy

I am sure someone else will be along with some suggestions for parts, but you can send the camshaft to Lunati cams and they can weld and regrind it back to stock.

Dave
by indian301
Sat Nov 21, 2015 2:47 am
Forum: 4's and up
Topic: 4AD grill replacement
Replies: 10
Views: 644

Re: 4AD grill replacement

There is a grill on ebay at the moment. Nothing to do with me.
by indian301
Tue Apr 21, 2015 1:30 am
Forum: 4's and up
Topic: 4AD Engine Parts
Replies: 11
Views: 1025

Re: 4AD Engine Parts

I have been using Egge engine parts in California for years. They had stainless steel valves for my 1930 Indian in stock!

Dave
by indian301
Tue Aug 20, 2013 7:11 pm
Forum: 4's and up
Topic: Electronic Ignition for 4AD ?
Replies: 27
Views: 7542

Re: Electronic Ignition for 4AD ?

Mark, You cannot buy a decent condenser anymore. I converted my Sunbeam over to Pertronix (change 3 condensers in less than 6 months, AZ heat?) and have been extremely happy with results. I would think if you crossed the distributor numbers over, the Lucas number would match another car and be readi...
by indian301
Sun Apr 28, 2013 4:26 am
Forum: General stuff about this board
Topic: What's everyone working on
Replies: 6
Views: 2754

Re: What's everyone working on

I am currently working on a 1930 Indian 4 cylinder motorcycle. One of my best friends was in a very bad accident on it and he did not want to ride again, so I bought it from him. I just finished rebuilding the engine after the cases were welded up. The frame looks like a pretzel, so I will be cuttin...
by indian301
Mon Jul 23, 2012 2:41 am
Forum: Events
Topic: Ottawa British Car Day
Replies: 3
Views: 2367

Re: Ottawa British Car Day

Where are the pictures?
by indian301
Mon Jul 23, 2012 2:40 am
Forum: 4's and up
Topic: 4AD Rear wheel bearing lock washers
Replies: 2
Views: 2421

Re: 4AD Rear wheel bearing lock washers

Why not just use a plain flat washer with Red Loctite? If you do need to take it off again a little heat with a propane torch will suffice.

Dave V-6 4AD
by indian301
Thu Oct 06, 2011 3:00 am
Forum: Pre-War
Topic: 2 Down, 1 1/2 to go
Replies: 11
Views: 4183

Re: 2 Down, 1 1/2 to go

Mike, Pertaining to the cracks in the block. When I used to drag race I used to concrete the lower half of the block for strength. Obviously I was only running a 1/4 mile at a time so overheating was never a problem. Depending on where the cracks are you could possibly concrete the block up to the f...
by indian301
Fri Sep 23, 2011 5:33 am
Forum: Events
Topic: STOWE 2011 A SUCCESS & WE ARE THE FEATURED MARQUE IN 2012!!!
Replies: 8
Views: 7875

Re: STOWE 2011 A SUCCESS & WE ARE THE FEATURED MARQUE IN 2012!!!

I would love to attend the gathering next year in my V6AD, but I am back at school and it would be a very long drive from AZ. I think my boss would have a fit if I took that much time off. Well you never know what might happen.

Dave V6AD
by indian301
Fri Sep 02, 2011 6:12 am
Forum: 4's and up
Topic: New member and Brake Job / Front Hub Seal question
Replies: 7
Views: 1824

Re: New member and Brake Job / Front Hub Seal question

If you can get an accurate outside diameter measurement for the sealing surface, where the seal rides (spindle) and an outside diameter measurement for where the seal is installed( brake drum), any good bearing supply company should be able to get you seals and bearings. I do this all of the time be...
by indian301
Mon Apr 04, 2011 2:45 am
Forum: 4's and up
Topic: Spring Driving
Replies: 2
Views: 1152

Spring Driving

Here in northwest Arizona the weather has been beautiful. I just removed the top and side curtains from my 6AD. What a blast to drive.

Dave

Go to advanced search